Auto-meter 1785 Bedienungsanleitung PDF herunterladen

FOR SERVICE CONTACT: AUTO METER PRODUCTS Inc. 413 W. Elm St., Sycamore, IL 60178 USA (815)899-0801 or

2650-655E 4/8/03

12 MONTH LIMITED WARRANTY

The manufacturer warrants to the consumer that this product will be free from defects in materials and workmanship for a period of twelve (12) months from the date of the original purchase. Products

that fail within this 12 month warranty period will be repaired or replaced at the manufacturer’s option to the consumer, when determined by the manufacturer that the product failed because of defects

in material or workmanship. This warranty is limited to the repair or replacement of parts in the instrument and the necessary labor done by the manufacturer to affect the repair or replacement of the

instrument. In no event shall this warranty exceed the original purchase price of the instrument, nor shall the manufacturer be responsible for special, incidental or consequential damages or costs

incurred due to failure of this product. Warranty claims to the manufacturer must be transportation prepaid and accompanied with dated proof of purchase. This warranty applies only to the original

purchaser of product and is non-transferable. All implied warranties shall be limited in duration to the said 12 month warranty period. Breaking the instrument seal, improper use or installation, accident,

water damage, abuse, unauthorized repairs or alterations voids this warranty. The manufacturer disclaims any liability for consequential damages due to breach of any written or implied warranty on all

products made by the manufacturer.

INSTALLATION INSTRUCTIONS

" ELECTRIC CLOCKS

2650-655E

Lens Cleaning

The clear lens on your clock

is made of acrylic plastic. To

prevent scratching caution

must be used when cleaning.

Use a mild, soapy solution and

soft cloth to clean. Wipe lightly.

INSTALLATION

To Good

Ground

Grommet

Twist- In

Light Socket

⁄

”

Thumbnut

and Lockwasher

To 12 volt terminal

on ignition switch

or to any constant

12V power source.

1. Disconnect negative (-) battery cable.

2. Mount gauge into dash or panel using mounting bracket

and hardware provided.

3. Using 18 gauge wire and female spade connector

(not provided). Attach female spade connector to the

negative (-) spade terminal on back of gauge and the

opposite end to a good engine ground.

4. Attach second wire to the positive (+) female spade

connector on back of gauge and the opposite end to 12

volt terminal on ignition switch or to any constant 12V

power source.

5. Reconnect negative (-) battery cable.

NOTE: To set clock, push in the set knob and turn

clockwise to the current time. When time is set,

make sure that the knob is in the out position

for proper operation.

Mounting

These gauges can be mounted in a 2

⁄16” dia. hole or in a

standard aftermarket street rod panel. Fasten with brackets

supplied as shown. (Hookup wire is required.) To assure

proper functioning of this instrument, please read instructions

thoroughly before installing.

FRONT MOUNTING

(SIDE VIEW)

To 12 volt terminal

on ignition switch

or other switched

12 volt source.

To Good

Ground

Replace light bulb with the same bulb

number that was removed.

CAUTION!

As a safety precaution the Red wire of this product

should be fused before connecting it to the positive

(+) side of the 12V DC battery. We recommend

using a 4 Amp, 3AG fast-acting type cartridge fuse

(Littlefuse

# 312 004 or an equivalent) inline with

the Red wire of our product.

SERVICE

For service send your product to Auto Meter in a well packed shipping carton. Please include a note explaining what the problem is along with your phone number. Please specify when you

need the product back. If you need it back immediately mark the outside of the box “RUSH REPAIR,” and Auto Meter will service product within two days after receiving it. ($10.00 charge will be

added to the cost of “RUSH REPAIR.”) If you are sending product back for Warranty adjustment, you must include a copy (or original) of your sales receipt from the place of purchase.

CAUTION!

As a safety precaution the Red wire of this product should be fused before connecting it to the

positive (+) side of the 12V DC battery. We recommend using a 4 Amp, 3AG fast-acting type

cartridge fuse (Littlefuse

# 312 004 or an equivalent) inline with the Red wire of our product.

" ELECTRIC CLOCKS 1

Inhaltsverzeichnis

Seite 1 - " ELECTRIC CLOCKS

FOR SERVICE CONTACT: AUTO METER PRODUCTS Inc. 413 W. Elm St., Sycamore, IL 60178 USA (815)899-0801 orEmail us at [email protected]

Verwandte Modelle: 1586 | 1484 | 1986 | 1885 | 1385 |

Kommentare zu diesen Handbüchern

Keine Kommentare

Auto-meter 1785 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Auto-meter 1785 herunter. Auto Meter 1785 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: 1586 | 1484 | 1986 | 1885 | 1385 |

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Auto-meter 1785